Set your transfer parameters

Before you can send tokens or messages, you'll need to set your parameters.

Now you're ready to set the parameters of your trade request. 
Example: Swap 0.05 WETH from Goerli and receive aUSDC on the Avalanche Fuji Tesntet
const params = {
    fromChain: 5, // Goerli testnet
    fromToken: "0xB4FBF271143F4FBf7B91A5ded31805e42b2208d6", // WETH on Goerli
    fromAmount: "50000000000000000", // 0.05 WETH
    toChain: 43113, // Avalanche Fuji Testnet
    toToken: "0x57f1c63497aee0be305b8852b354cec793da43bb", // aUSDC on Avalanche Fuji Testnet
    fromAddress: "0xAD3A87a43489C44f0a8A33113B2745338ae71A9D", // ethers.signer.address; transaction sender address
    toAddress: "0xAD3A87a43489C44f0a8A33113B2745338ae71A9D", // the recipient of the trade
    slippage: 1.00, // 1.00 = 1% max slippage across the entire route
    enableForecall: true, // instant execution service, defaults to true
    quoteOnly: false // optional, defaults to false
};
Due to low liquidity on testnet, we ask that you limit your trade size in most cases to less than 0.1 of the native gas token (e.g. <0.1 ETH, or AVAX).
Note that the same token types (i.e. USDC) often has a different address on each chain. Make sure you've checked the address is right for the chain you are sending from/to. 
Params are structured as aMapChainIdName object. A GetRoute object describes a desired any-to-any transfer. It is defined by the following interface:
Request Params:
Property
Description
fromChain
Source Chain ID​
fromToken
Address of the sending tokens
fromAmount
Amount of tokens to be sent in WEI
toChain
Destination Chain ID​
toToken
Address of the receiving tokens
fromAddress
Transaction sender address. Will be also used as a fallback address for the source chain
toAddress
The expected output address that will receive the destination tokens
slippage
Max slippage across route, (0.3-99.99) 1 = 1% slippage.
enableForecall (optional) 
Instant execution on the destination chain when set to true. Defaults to true.
quoteOnly (optional) 
If true, returns only a quote for the route. Omits transaction data needed for execution. Defaults to false
prefer (optional) 
When set, the route response will prefer routes from the DEX corresponding to the string. See possible strings here.
Sending/receiving native tokens
If you want to send or receive native tokens (i.e ETH), the sourceTokenAddress or destinationTokenAddress arguments must be set to 0xEeeeeEeeeEeEeeEeEeEeeEEEeeeeEeeeeeeeEEeE
Once you have configured the params object, the next step is to get a route​

Property	Description
fromChain	Source Chain ID
fromToken	Address of the sending tokens
fromAmount	Amount of tokens to be sent in WEI
toChain	Destination Chain ID
toToken	Address of the receiving tokens
fromAddress	Transaction sender address. Will be also used as a fallback address for the source chain
toAddress	The expected output address that will receive the destination tokens
slippage	Max slippage across route, (0.3-99.99) 1 = 1% slippage.
enableForecall (optional)	Instant execution on the destination chain when set to `true`. Defaults to `true`.
quoteOnly (optional)	If `true`, returns only a quote for the route. Omits transaction data needed for execution. Defaults to `false`
prefer (optional)	When set, the route response will prefer routes from the DEX corresponding to the string. See possible strings here.

Example tokens response

Get a route

Last modified 1mo ago